HTS 7409 — Copper Plates, Sheets, and Strip
Copper plates, sheets and strip, of a thickness exceeding 0.15 mm. Column 1 below is the general rate on each rate-bearing line in USITC 2026HTSRev21. A statistical suffix of one of those lines has an empty general cell and takes that line's rate.
Column 1 General
1% to 3%
Seventeen rate-bearing lines. The rates are 1%, 1.7%, 1.9%, and 3%. There is no single heading rate.
Section 232 copper
50%
The rate this site already publishes on modeled chapter 74 headings. This page does not add 7409 to the calculator.
Column 1 by line
| HTS | Description | Column 1 |
|---|---|---|
| 7409.11.10.00 | Of refined copper › In coils › Of a thickness of 5 mm or more | 3% |
| 7409.11.50 | Of refined copper › In coils › Of a thickness of less than 5 mm | 1% |
| 7409.19.10.00 | Of refined copper › Other › Of a thickness of 5 mm or more | 3% |
| 7409.19.50.00 | Of refined copper › Other › Of a thickness of less than 5 mm › Of a width of 500 mm or more | 1% |
| 7409.19.90.00 | Of refined copper › Other › Of a thickness of less than 5 mm › Of a width of less than 500 mm | 3% |
| 7409.21.00 | Of copper-zinc base alloys (brass) › In coils | 1.9% |
| 7409.29.00 | Of copper-zinc base alloys (brass) › Other | 1.9% |
| 7409.31.10.00 | Of copper-tin base alloys (bronze) › In coils › Of a thickness of 5 mm or more | 3% |
| 7409.31.50.00 | Of copper-tin base alloys (bronze) › In coils › Of a thickness of less than 5 mm › Of a width of 500 mm or more | 1.7% |
| 7409.31.90.00 | Of copper-tin base alloys (bronze) › In coils › Of a thickness of less than 5 mm › Of a width of less than 500 mm | 3% |
| 7409.39.10 | Of copper-tin base alloys (bronze) › Other › Of a thickness of 5 mm or more | 3% |
| 7409.39.50.00 | Of copper-tin base alloys (bronze) › Other › Of a thickness of less than 5 mm › Of a width of 500 mm or more | 1.7% |
| 7409.39.90 | Of copper-tin base alloys (bronze) › Other › Of a thickness of less than 5 mm › Of a width of less than 500 mm | 3% |
| 7409.40.00.00 | Of copper-nickel base alloys (cupro-nickel) or copper-nickel-zinc base alloys (nickel silver) | 3% |
| 7409.90.10 | Of other copper alloys › Of a thickness of 5 mm or more | 3% |
| 7409.90.50 | Of other copper alloys › Of a thickness of less than 5 mm › Of a width of 500 mm or more | 1.7% |
| 7409.90.90 | Of other copper alloys › Of a thickness of less than 5 mm › Of a width of less than 500 mm | 3% |
Source: USITC HTS export, release 2026HTSRev21, retrieved 2026-10-29. exportList for heading 7409. Special (preference) rates are not applied.
Section 232
Modeled chapter 74 headings on this site publish a 50% Section 232 column: 7403, 7407, 7408, 7411, and 7419. The October 18, 2026 correction for heading 7403 says Section 232 copper stays 50%. The copper guide lists 7409 in that covered set.
The notice this site cites for the April 6, 2026 adjustment is Proclamation 11021 of April 2, 2026, Federal Register 2026-06960 (91 FR 18201). The citation stored for that notice says the annex is image-only and that no heading-wide derivative rate is set from it. This page does not parse that annex, does not invent a 25% derivative rate for 7409, and does not put 7409 into the duty calculator.
No Section 301 column is published for 7409. Headings 7407, 7408, 7411, and 7419 publish 25% for China. Heading 7403 publishes N/A. Those figures are not copied onto 7409.
For a calculated copper stack, use a heading the calculator already has, such as HTS 7408 in the tariff calculator.